Відео

It's only working on port the wireless visibility is off can't see it 😢

I would appreciate if you would show how can i connect to my master router via Cable and not WLAN1 !? I want to have a bridge acess point connected via cable. You didn't show it.

really work! GJ MAN!

EXCELLENT Information and well formulated lesson! Thank You!!!

Hi!!! Im new in mikrotik, is it possible to update how to identify users using bittorrent for the new OS versions please? since the PTP was removed from the the options

Why do you need bridge for that, can't we do directly on the interface?

tanks 4 watching xd

Fantastic thank you😎

How to pause time when user disconnect

Can i have your contact number or mail please?

I am Microtik greenhorn. Thanks for doing this.

Fantastic! Thanks.

Thank you x 1billion

Thank you!!!

Very clear and patient presentation. Soothing and educative. Thanks sir.

Excellent, thanks.

اداء رائع جدا ...

I would like some help with my mikrotik router can I get some help from you

can i install router os in tp link tl-mr3420 v5

Great videos Sir. may you make a video on ; Mikrotik router dhcp, vlans with a cisco switch ?

Incomplete information

Thank you for the great tutorial But you didn't show us how to open the main page router before start configure it

Will the same method work on more than 2 connections?

My country is Iraq but I found it’s wrote ESTI So the minimal antenna gain is 3 How can I fix that ?

Sir, the other traffic counts also for gaming? is it okay to put in packet mark = nomark? this is new to me.. since other tutorial used prerouting.

Thank you for your efforts. I could not remember the correct speed and settings for serial connection to my MikroTik CRS317 and I remembered your video...so a second time found it and even more useful this time as the router had got stuck in a loop and serial cable access allowed me to get it to boot into the right OS. A BIG THANK YOU

totally useless there is no interface wireless conmand. there is no print detail advanced command anymore,

Thank you

reject is bad practice, consider drop.

This is not not for me, I don't know why, but

Is this config is better than Pcc?

when i am writing port and ip address in udp section in setup below it shows tcp: server not started......udp: server not started

if the IPs in wan ports are assigned statically how can we do load balance?

thank you sir

What if this go over cambium ptp radio links? What's the set-up going to look like?

Great video, thanks a lot for sharing it, I've followed step by step your instructions and it worked great.

How do i unblock my mac address from my mikrotik winbox

Please in Phone 😢

Thank you for showing this, I was about to return my hap ac3, couldn't wrap my head with all the instructions until I found your vid.

awesome, thanks...

Always best! Thanks.

Always best! Thanks.

Wasted my time

What I usually do to increase wifi signal strenght is to change frequency Mode to manual tx. (Where the mouse is at 5:07)

at the quick set: I stoped watching, I wanted to know what are those other options do, as I getting started the title says, im not sure if my question will be answered soon, I rather check other tutorials bye

Well done, my friend. Your narration was helpful and I am grateful that you explained each step, including your advisory to exercise care when dealing with the high voltage components. I also appreciate your graphic text message as well as your selection of smooth jazz music in the background, my friend. Please keep up the good work.😂

Thank you for the video. Very informative, quick one how can you use hotspot(user manager) feature on m2 .. the m2 acts as a hotspot while mikrotik manages users log in

❤❤❤Thank you so much Bro❤❤❤

Is there a solution for a MikroTik setup experiencing issues with hotspot ports when both ISPs are connected for load balancing and failover, yet functioning properly when one ISP is disconnected? The LAN-configured ports are working fine on both ISPs. Thanks